FAAC Welding & Fabrication Nationwide

FAAC Welding & Fabrication: The Euless Owner’s Guide

We stock and install FAAC-compatible welding and fabrication parts for gate hinges, post mounts, operator brackets, and swing-arm reinforcement, with most Euless jobs priced between $350 and $900 installed depending on the scope of the fabricating work. Our trucks carry common FAAC bracket sets, hinge weld plates, and steel stock, so a technician can usually complete the fabrication and welding in a single visit. Most owners discover the problem the hard way: the gate starts dragging, the operator bracket pulls loose from the post, or a weld cracks and the whole gate sags an inch or two on the hinge side.

Call (806) 484-1837

The Mid-Cities clay soil is the quiet culprit behind a lot of FAAC fabrication failures we see in Euless. Posts shift over the years, the gate’s geometry drifts, and suddenly the opener is pushing against a gate that no longer swings true. That strain lands on the welded brackets and hinge plates first. By the time a homeowner calls us, the metal has usually been flexing for months.

Which FAAC Models This Applies To

This page covers the welded and fabricated steel components that hold FAAC swing-leaf gates in place: operator mounting brackets, hinge weldments, post reinforcement plates, and gate leaf repair sections. The FAAC product line we see most in Euless driveways includes the 412, 415, 770, and 390 swing operators, along with the newer S418 and C720 series. The bracket pattern on a 412 operator does not match a 770, and the post footprint is different enough that a bracket for one will not line up on the other without a welder and a field modification.

Here is the compatibility gotcha worth knowing: FAAC swing operators use metric mounting hardware and specific bracket geometry. A generic bracket from a big-box store will usually place the operator arm at the wrong pivot height, which shortens the life of the operator and the gate. We match the bracket to the FAAC series and the gate’s weight and leaf length, then weld it square to a reinforced plate on the post. For most older FAAC operators, we recommend OEM brackets when they are available; for hinge weldments and post plates, a properly fabricated steel equivalent serves just as well and often outlasts the original. Ironworks Gate Co. is an independent service provider, not affiliated with FAAC, but our technicians are trained on their equipment across the years and we carry the common wear parts on the truck.

Signs Your FAAC Welding & Fabrication Is Failing

• The gate sags at the latch end when closed. A sagging leaf usually means the hinge weld on the post or the gate has cracked or the hinge plate has begun tearing away from the post. The metal is still hanging on, but it is flexing every time the gate cycles, and it will not heal itself.
• The operator bracket wobbles or pulls away from the post. FAAC operators push and pull with steady force, and over time a wobbly bracket works its anchor bolts loose. If you can rock the operator by hand, the bracket needs to be re-welded or replaced before it tears free completely.
• The gate makes a cracking or popping sound when opening. That sound is metal on metal, usually a cracked weld opening and closing under load. It gets louder as the crack grows, and the next step is a weld that lets go mid-cycle.
• The gate binds or scrapes against the driveway or a post. When welded components shift, the gate leaf moves out of alignment and the FAAC operator has to work harder to push it through the arc. Extra strain on the operator shortens its life and burns through the motor’s internal components faster.
• Fresh rust streaks below the hinges or brackets. Rust staining almost always means moisture has gotten inside a cracked weld or between the bracket and the post. By the time you see the streak, the crack is already open and spreading with every cycle.

Replacement Cost & What’s Included

For Euless homes, expect a typical installed price between $350 and $900 for FAAC welding and fabrication work, with most jobs landing around $500 to $650. The range depends on what failed and how much steel has to be cut out, re-fabricated, and re-welded. A simple operator bracket replacement and re-weld runs toward the lower end. A full hinge plate rebuild on a heavy estate gate with post reinforcement falls toward the top, especially if we are also straightening a sagging leaf.

Every quote includes the parts, the fabrication time, the welding, field cleanup, and a test cycle of the gate with the FAAC operator in place. The price is written and agreed before we strike an arc, so there are no surprises on the bill. All work carries our 90-Day Done Right Promise in writing: if it is not right, we come back and make it right, no paperwork, no arguing.

Key Takeaways

• FAAC bracket and hinge failures are usually weld fatigue, not part failure.
• We match brackets to the specific FAAC series: a 412 bracket will not fit a 770.
• Installed pricing for Euless runs $350 to $900, quoted and agreed before work starts.
• Most repairs are completed in one visit, including fabrication and welding.

DIY or Call Us?

Welding on a gate that carries a FAAC operator is not a weekend project, and we do not recommend it. The gate leaf is heavy, the springs and operator arms are under tension, and a bad weld on a hinge or bracket can drop a several-hundred-pound gate on whoever happens to be standing near it. A cracked weld is also an electrical safety concern if the operator’s ground path runs through the gate frame, which it often does. This is one repair where the risk of doing it wrong is genuinely serious, and the cost of a professional fix is modest compared to a failed gate hitting a car or a person.

What an owner can safely do is document the problem: take photos of the cracked or sagging area, note the FAAC model number on the operator label, and call us. We will ask about the gate’s age, leaf length, and what it is doing, then quote the job over the phone. Call (806) 484-1837 and Victor or one of our technicians will walk you through it.

FAQs