Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Motor Replacement: The Euless Owner’s Guide
We stock and install Linear-compatible gate motors for Euless driveways, with most replacements running between $850 and $1,650 installed depending on your model and the condition of the existing mounting hardware. Our trucks carry the most common Linear swing and slide motor replacements, so a single visit usually gets your gate working again. Most Euless homeowners discover the motor has failed the same way: the gate stops responding to the remote halfway through a rainstorm, or it starts moving in jerks before quitting entirely mid-cycle.
This page covers what fails, which Linear models we can match, what a replacement actually costs in the Euless market, and how we handle the swap so you’re not out there with a stuck gate longer than necessary. We’re an independent gate company, not affiliated with Linear, which means we have no reason to push a part your gate doesn’t actually need. If your motor can be repaired honestly, we’ll tell you that first.
Key Takeaways
- Linear gate motor replacement in Euless typically costs $850-$1,650 installed
- We stock Linear swing and slide motor replacements on the truck
- Most replacements are completed in a single visit
- Every job carries the written 90-Day Done Right Promise
- We service Linear plus eight other major gate automation brands
Which Linear Models This Applies To
Linear has produced gate operators under several model lines over the last twenty-plus years, and the compatibility gotchas matter more than most people expect. The big split is swing versus slide: Linear’s swing arms (the L-Series and the older Sentex line) use a different actuator profile than their slide gate motors, and the mounting brackets are not interchangeable. We see a fair number of Euless gates that were originally installed with a Linear LRA or L-series swing actuator still running on the original arm, with the control board being the part that actually died.
The model number lives on a metal tag riveted to the motor housing or on the control board itself. Look for a number starting with “L” followed by digits (L0500, L1800, and the older LS and SL series) or an APeX board number. If you can’t read the tag, our technicians can match the part by the arm’s diameter, the gearbox type, and the mounting hole pattern. Linear changed their motor shaft dimensions between some model years, so a motor that “looks identical” from a different generation may not seat correctly. On OEM versus aftermarket: for Linear specifically, we have had good service from OEM Linear replacement motors and from a small number of quality aftermarket equivalents that cross-reference cleanly. The cheapest no-name motors on the internet often claim broad compatibility and deliver neither the torque rating nor the duty cycle your gate needs. We match by torque spec, not just by the marketing box.
Signs Your Linear Gate Motor Replacement Is Failing
- The gate moves slower than it used to, especially in cold weather. Linear motors with worn internal gears or tired capacitors lose torque first at low temperatures. A gate that takes twice as long to open in January as it did in July is telling you the motor is working harder than it should be.
- The gate stops mid-travel and reverses. This usually points to a failing limit switch or a motor drawing too much current, which trips the obstruction sensing circuit. Linear operators are designed to stop rather than crush, so a hypersensitive reverse is a motor or board issue, not a misbehaving gate.
- You hear a humming sound but the gate doesn’t move. When the starter capacitor fails, the motor hums without turning the arm. This is a classic Linear failure after Texas heat cycles: the capacitor swells, leaks, and quits. Sometimes replacing just the capacitor gets you more life, but a motor that has burned through one capacitor will often burn through another.
- The gate jerks or stutters instead of moving smoothly. Worn drive gears or a failing bearing inside the operator housing cause the arm to catch and release. By the time the motion is visibly jerky, the gear wear is usually advanced enough that rebuilding doesn’t make economic sense compared to replacing the motor.
- The remote and keypad both fail to move the gate, but you hear a click at the board. This is the board trying to send power to a motor that won’t turn, usually because the windings have shorted or the gearbox has seized. If the click is there, the controls are fine; the motor is the problem.
Replacement Cost & What’s Included
In Euless, a complete Linear gate motor replacement runs between $850 and $1,650 installed. The range comes down to three things: swing versus slide (slide motors run higher because of the additional drive components), whether we’re keeping your existing Linear board or replacing it along with the motor, and whether the mounting brackets or arms need fabricating or reinforcing. We give you one written, itemized price before any work starts, covering the motor, labor, and any brackets or hardware the job requires. There is no separate trip charge on a completed replacement. Every replacement we install is protected by our 90-Day Done Right Promise: if it isn’t right, we come back and make it right. No paperwork, no argument.
If you have a written estimate from another company, bring it to us. We’ll give you a free second opinion on it, and our price will be settled before a single bolt gets turned.
DIY or Call Us?
There are a few things any Euless homeowner can safely check before calling us: confirm the breaker hasn’t tripped, check that the photo eyes aren’t blocked by leaves or spider webs, and visually inspect the gate itself for obvious binding in the track or at the hinges. Those checks cost you nothing and occasionally save a service call. What you should not attempt is opening the Linear operator housing and removing the motor yourself. These motors are wired to line voltage, the capacitor retains a charge even with the power off, and the swing arm is under mechanical tension. Every year we get called to fix a gate where a well-meaning homeowner opened the case, got a shock or a pinched hand, and ended up with a half-disassembled operator and a bigger bill than the original problem.
If you’re reasonably handy and the failure is clearly a capacitor, that is a fifteen-dollar part and a ten-minute job for someone who works with electrical components. But if the motor itself is seized or the gearbox is grinding, that’s our work. The honest test: if you wouldn’t open the back of your air conditioner, don’t open a Linear gate motor. Call us at (806) 484-1837 and we’ll send someone who does this every day.
FAQs
A Linear gate operator in the Euless climate typically lasts 8 to 12 years, with heat and humidity being the main killers of capacitors and circuit boards. Gates that are properly maintained with a seasonal tune-up tend to hit the upper end of that range. We offer an $89 Seasonal Tune-Up that catches the small problems before they become motor failures.
Sometimes yes. Capacitor failures, limit switch problems, and wiring faults are all repairable, and we will always quote a repair when the motor is salvageable. When the gearbox has seized or the motor windings are shorted, replacement is the only honest option. We walk you through exactly what we found before you approve any work.
Most Linear motor replacements are completed the same day we arrive, usually within two to three hours including set-up and testing. Slide gates with worn drive components can run longer because the drive rail and chain may need attention while we are in there. We’ll tell you the time frame before we start, and we’ll be there when we say.
Yes. Our service vehicles carry Linear swing and slide motor replacements, capacitors, limit switches, and control boards for the most common Linear series. For less common models, we can usually have the correct part in hand within one to two business days. We also stock replacement parts for LiftMaster, Mighty Mule, and Ghost Controls systems.
As Victor Salinas puts it: “A gate should open when you need it to and stay closed when you don’t. That’s the whole job.” Victorgrew up in Euless, not far from Bear Creek Park, and he has spent the better part of three decades replacing and repairing gate motors across the Mid-Cities. He knows which Linear parts fail first in Texas heat and which ones are worth repairing.
Get Your Linear Gate Motor Replaced in Euless
If your Linear operator is dead or dying, don’t spend another week fighting with a gate that works when it feels like it. Call (806) 484-1837 and a live person will answer, day or night. We’ll set up a visit at a time that works, give you a written price before any work starts, and stand behind the replacement with the 90-Day Done Right Promise. Senior and veteran customers receive a 5% discount, and repairs over $250 carry $50 off. That’s the square deal: upfront price, no surprises on the bill, and a gate that works like it’s supposed to.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Euless and nearby areas.