Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Irving
A gate access control system in Irving typically costs $450 to $2,800 depending on whether we’re adding a keypad to an existing opener or building out a full phone-entry and card-reader system at an HOA entrance. Most repair work, like a dead keypad or a fried control board, runs $180 to $540 and we can usually get to it the same day. Call (806) 484-1837 and a live person answers, day or night.
We work on gates all over Irving, from the gated subdivisions off MacArthur Boulevard to the corporate campuses tucked into Las Colinas. When an access system fails, it’s rarely convenient. Our crews know the streets, the HOAs, and the specific equipment this city runs on better than any shop coming in from Dallas.
Why Ironworks Gate Co. Is Irving’s Preferred Gate Access Control Company
We’ve been at this for over 42 years, founded back in 1984, and we plan to be here another forty. Our Gate Access Control team works Irving neighborhoods every week, which means when a keypad dies at a Las Colinas HOA gate off O’Connor Road, we don’t need a map app to find it.
Victor Salinas leads our crews, and he holds every technician to one standard: the job is done right, and it’s backed in writing. That’s the 90-Day Done Right Promise. No paperwork, no arguing. If it’s not right, we come back and make it right.
The Las Colinas district in particular runs on legacy FAAC and Elite swing-gate operators installed during the 1980s and 1990s buildout. Generalist shops struggle to source boards and limit switches for those units. We don’t. We know the parts ecosystem for those European-brand operators because we’ve been servicing them in Irving for decades.
Our Gate Access Control Services in Irving
Keypad Entry
Keypad entry is the most common access system on Irving residential gates, especially in Las Colinas HOA communities where every resident gets a code and the gate has to work for hundreds of cars a day. A new wired keypad with weatherproof housing typically runs $250 to $485 installed. If the existing keypad is fine but the control board behind it failed, that’s a separate repair usually in the $180 to $340 range.
One thing we see constantly in Irving is keypad failure after power surges. Those legacy FAAC swing gate operators in Las Colinas lose their limit switch memory after a surge, the gate stalls mid-travel, and the keypad goes unresponsive. We stock the replacement boards and limit switches locally, so most of those jobs are one visit.
Phone Entry
Phone entry systems let a homeowner or corporate campus visitor call a number that opens the gate. In Irving this is common on the larger estates north of 114 and on commercial properties where a guard shack isn’t staffed at night. A basic cellular phone entry module runs $600 to $1,400 installed. Full multi-tenant systems for an HOA or office campus run higher, $1,800 to $4,500 depending on line count and whether we’re integrating with an existing card reader.
We see more phone entry demand in Irving than in nearby cities because of the density of corporate campuses in Las Colinas. Those properties need visitor management that doesn’t require a full-time guard, and a phone entry system tied to the front desk is the practical answer.
Card Reader
Card readers are the workhorse of commercial access control, and Irving’s Las Colinas corporate corridor runs on them. A proximity card reader installed at a swing or slide gate typically runs $500 to $1,200 per reader, plus the control panel integration. Most of the commercial gate access work we do in Irving involves retrofitting readers onto gates that were originally built with keypads only.
For HOA communities considering a card reader upgrade, we typically recommend a system that supports both fobs and keypad codes. That way residents who have been using codes since the 1990s don’t have to change habits overnight. It’s not a one-size-fits-one answer; it depends on the gate and the community.
Video Intercom
Video intercom has grown fast in Irving, particularly on the newer estate properties around Valley Ranch and the rebuilds happening in older west Irving. A single-panel video intercom with a mobile app connection typically runs $1,100 to $2,600 installed. The number that moves is the wiring: if we’re pulling new cable to the house, the job costs more than if we’re tying into existing conduit.
For homeowners, a video intercom means seeing who’s at the gate before you open it. For HOAs in Irving it means a visual record of every entry, which some insurance carriers now ask for.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Irving
We’re trained and equipped on nine gate-automation brands, including FAAC, Mighty Mule, and LiftMaster, which covers nearly every opener on an Irving driveway or campus. The practical benefit to you is that when we show up, the fix is usually made on the first visit because we already know the unit. No ordering parts and waiting two weeks. For legacy FAAC operators in Las Colinas, we keep the specific boards, limit switches, and capacitors those units eat through on the truck.
Common Gate Access Control Problems We See in Irving Homes
Irving’s specific conditions create specific failures. Here’s what we actually see in the field, week after week:
– Keypads and control boards failing after power surges in Las Colinas. The area’s dense commercial grid sees more surge events than the older residential streets, and legacy FAAC boards are the usual casualty. The gate stalls mid-travel, the keypad flashes, and the entrapment sensor trips. We replace the board, reset the limit memory, and the gate runs true again.
– Hinge posts heaving out of plumb on Blackland Prairie clay. Irving sits on highly expansive clay that swells with spring rain and shrinks hard in August. When a hinge post moves, the gate binds, the operator strains, and eventually the gearbox strips. At a Las Colinas HOA off O’Connor Road, we replaced a failed FAAC 412 swing gate operator, rewired the keypad entry, and then reset the hinge post that had heaved forward on that same clay so the new operator wouldn’t labor on cold starts.
– Winter Storm Uri damage to commercial slide gates. The February 2021 freeze seized gearboxes and cracked hydraulic lines on slide gates at corporate campuses across Irving. Operators not rated for sustained subfreezing temperatures simply failed. We’ve since upgraded a number of those systems to subzero-rated gearboxes.
– Rack and pinion binding on slide gates in older west Irving neighborhoods. When clay movement shifts the track, the rack and pinion bind, the motor draws more current, and the gearbox strips. The gate won’t close at the keypad, which reads as a control problem but is actually mechanical. We correct the post and track alignment before swapping any electronics.
Pricing for Gate Access Control in Irving, TX
What moves the price on an Irving job is usually the gate’s age and the soil it sits on. A gate that’s been heaving on clay for thirty years takes longer to bring back into plumb than one on a newer slab. The quote we give you is the price you pay, agreed before any work starts. No surprises on the bill. Free estimates, and we honor a 5% Senior and Veteran discount on every job, always.
We Also Serve Cities Near Irving
While most of our gate access control work in this corridor happens right here in Irving, we also run calls to Grand Prairie, Coppell, Euless, and Grapevine. If you’re just outside the city line and need a gate looked at, call us. We’ll tell you straight whether we can get to it this week.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Irving
Why does my gate access control keypad work inconsistently after a North Texas freeze?
The keypad itself is rarely the problem. What usually happens after a hard freeze in Irving is that condensation inside the control board housing shorts a relay or the voltage regulator on the board, causing intermittent keypad response. The fix is replacing the board and sealing the housing against moisture, which runs $180 to $340. If the keypad has been wet-failed entirely, a new keypad runs $250 to $485. Call (806) 484-1837 and we’ll diagnose it over the phone before rolling a truck.
My slide gate opener recently started grinding and reversing - is that a control board problem?
Usually not. On Irving’s expansive clay soils, the more common cause is the post or track shifting out of alignment, which binds the rack and pinion. The motor draws extra current, overheats, and the gate reverses as a safety response. The control board is just doing its job. We straighten the post and track before touching the electronics, because replacing a board on a misaligned gate just burns up the new board too.
Can I add smartphone access to my existing HOA gate in Las Colinas without replacing the whole system?
Yes, in most cases. A cellular or Wi-Fi bridge module ties into your existing operator’s control board and lets residents open the gate from a phone app while keeping the current keypad and card reader working. Installed cost in Irving typically runs $600 to $1,400 depending on the operator brand and whether we need to upgrade the board first. Legacy FAAC and Elite units sometimes need a board swap first, which we’ll quote before any work starts.
My gate opener at a corporate campus in Las Colinas keeps blowing fuses after a power surge. What’s happening?
That’s a classic symptom of a surge-damaged capacitor on the operator’s motor start circuit. When the capacitor shorts, the motor draws locked-rotor current and blows the fuse on every start. The real fix is replacing the capacitor and adding surge suppression at the disconnect, not just swapping fuses. We see this pattern regularly on commercial campuses in Las Colinas because the area’s grid density makes surge events more common than in the residential districts.
Why does my solar gate opener on a rural Irving property run slow or not at all after a cloudy week?
North Texas gets long stretches of overcast weather in winter and early spring, and a solar panel sized for summer sun won’t keep the battery topped off through a week of gray skies. The opener runs slow because the battery voltage is sagging. The fix is usually a larger panel and a deep-cycle battery upgrade, which runs $400 to $900 installed. If you’re on the rural edges of Irving with a long driveway, we’ll size a system that actually matches your gate’s duty cycle instead of the one-size panel that came in the box.
Call Ironworks Gate Co. for Gate Access Control in Irving
When a gate access system fails, you need it fixed now, and you need it fixed so it doesn’t fail again in three months. That’s the job we’ve been doing for over 42 years. A live person answers at (806) 484-1837, 24 hours a day, 7 days a week. We’ll give you a straight answer and a written quote before any work begins. $50 off any repair over $250, free second opinions on written estimates, and an $89 seasonal tune-up if your system just needs attention before it fails.
Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Irving and the surrounding metroplex with gate access control since 1984.