Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Euless: What to Know First
FAAC gate installation in Euless typically runs from $1,800 to $4,200 for a complete single swing gate system, with sliding gates landing between $3,000 and $6,500 depending on gate weight and track length. We complete most FAAC installations in one to two days and quote the full price before any work begins. If you’re in Euless and your FAAC opener needs a fresh gate, a new motor, or a full system replacement, this page tells you what to expect, what it costs, and why we do it differently. Call (806) 484-1837 for a free estimate.
How FAAC Products Fail - and How We Fix Them
FAAC builds durable hydraulic and electromechanical openers. After three decades of installing and servicing them across Euless driveways, we know exactly where they wear and what to do about it. Here are the failure patterns we see most often on FAAC systems in this area:
- E024 hydraulic pump seal leaks on the 400 series. The FAAC 400 operator runs on hydraulic pressure, and the pump seal is a known wear point after seven to ten years of North Texas heat cycles. The gate slows, groans, or stops mid-travel. We replace the seal and refill with the correct hydraulic fluid, or swap to a remanufatured pump when the original housing is scored. This is the single most common FAAC issue we correct in Euless.
- Bluebus communication faults on C720 and C721 models. The two-wire Bluebus system is clean when it works, but a nicked wire sheath or moisture intrusion at a splice point drops the bus voltage and throws a fault code on the control board. We trace the wire, find the compromised section, and re-pull or re-terminate the run. On Euless properties with older conduit, we often replace aged low-voltage wiring altogether to stop repeat faults.
- Limit switch drift on the 844 series. FAAC 844 operators use magnetic limit switches that can shift slightly with gate-post settlement. The gate opens too far or not far enough, then reverses or faults. We reset the limits, check the gate’s physical travel for interference, and re-secure the magnets. If the post has moved, we address the post first. A limit reset alone won’t hold on a settled post.
- Battery degradation in FAAC’s 24V solar-capable boards. Many Euless homeowners choose battery backup on their FAAC systems, and the sealed lead-acid batteries in those enclosures last roughly three to five years in Texas heat. The system works on AC power but fails when the power blinks. We load-test the batteries, replace them in pairs, and confirm the charging circuit is healthy.
- Aftermarket hydraulic fluid contamination. FAAC pumps are picky about fluid. We have opened more than one 400-series pump that was topped off with generic hydraulic oil from an auto parts store, which foams under load and destroys the pump. We use FAAC-spec hydraulic fluid and flush the system when contamination is present. This is a parts nuance you won’t find in the installation manual.
Our FAAC Gate Installation Process
Every FAAC installation in Euless follows the same sequence. No shortcuts, no surprises.
- 1
Site walk and measurement. We measure the gate leaf, weigh it by spec or estimate by construction, check the post depth and hinge condition, and confirm available power. If the existing gate is salvageable, we say so.
- 2
Equipment recommendation. We recommend the FAAC model that fits the gate’s duty cycle and weight, not the most expensive unit on the shelf. For a typical Euless single swing gate, that’s usually a 400 series. For a heavier double gate, a 750 or 884 depending on leaf weight.
- 3
Written price before work starts. You get the full number in writing. Labor, opener, hardware, any electrical work, and cleanup. Nothing is billed after the fact without your approval.
- 4
Installation. We set the operator, run the power per local code, mount the control board, wire the safety edges and photocells, and program travel limits and force settings. On FAAC systems, we follow OEM wiring diagrams to the letter to keep any remaining manufacturer warranty intact.
- 5
System test and cycle run. We cycle the gate twenty to thirty times, test obstruction detection with a physical block, and verify the manual release works. If the gate is connected to an intercom or keypad, we test that too.
- 6
Cleanup and walkthrough. We leave the site clean, hand you the written 90-Day Done Right Promise, and walk you through basic operation and what to watch for. Then we leave, and the gate works.
What FAAC Gate Installation Costs in Euless
Prices below reflect what we quote on FAAC work in Euless. Every job gets a written estimate before we order parts or turn a wrench.
- Single swing gate with FAAC 400 operator: $1,800 – $2,800 installed
- Double swing gate with FAAC 750 or 884 pair: $3,200 – $5,400 installed
- Sliding gate with FAAC 844 operator: $3,000 – $6,500 installed, depending on gate weight and track work
- Opener-only replacement (labor and unit, existing gate kept): $1,200 – $2,200
- Photocell, safety edge, or keypad addition during install: $180 – $450 per device
What moves the price: gate weight and construction, post condition, electrical distance from the panel to the operator, whether the gate is swing or slide, and whether we’re reusing existing hardware or replacing hinges and stops. We quote the number and hold to it. Call (806) 484-1837 and we’ll schedule a free measurement and written estimate.
Why Euless Homeowners Call Ironworks Gate Co. for FAAC Work
We’ve been in the Mid-Cities since 1984, and Victor Salinas grew up in Euless, not far from Bear Creek Park. That means when we quote an FAAC installation on an Euless driveway, we understand the local soil movement, the summer heat load on hydraulic components, and the homeowner expectation that a gate simply works. Every FAAC job leaves our shop covered by the 90-Day Done Right Promise in writing. If something is not right, we come back and make it right. No arguing, no paperwork. We also service eight other opener brands, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing among them, so when your Euless property has more than one gate or a mixed-brand setup, one visit handles it. We show up when we say we will, in uniform, background-checked, and we quote the price before we start. That is the whole arrangement.
FAQs
We are an independent FAAC service provider, not an authorized FAAC dealer, so manufacturer warranty claims go through FAAC directly. That said, we install FAAC equipment to OEM specifications so any remaining manufacturer warranty stays intact, and our own 90-Day Done Right Promise covers our labor and installation in writing. Call (806) 484-1837 if you’re unsure whether your FAAC unit is still under warranty, and we’ll help you sort it out.
Yes, and in many Euless homes that’s the smarter move. If your gate leaf is structurally sound and the hinges and posts are in good shape, we can mount a new FAAC opener, wire the controls, and set travel limits without replacing the gate itself. We’ll tell you honestly whether the existing gate is worth keeping or if you’d save money long-term by replacing both together. Estimates are free.
For a standard FAAC swing gate installation, we usually schedule within five to seven business days after the measurement visit. Sliding gate work and jobs requiring new concrete pads or longer electrical runs may take a bit longer to coordinate. Repair work, including a failed FAAC opener on an existing gate, we can often handle same-day or next-day. Call (806) 484-1837 and a live person will give you a straight answer on timing.
We use genuine FAAC components on any part that affects safety, force control, or warranty standing: control boards, hydraulic pumps, limit assemblies, and safety devices. For routine wear items like batteries and certain mounting hardware, we use quality aftermarket parts where they match or exceed OEM spec. We’ll tell you which parts are which before we order them, and the price is agreed before installation begins.
Slow FAAC gate movement is usually a hydraulic issue: low fluid, a failing pump seal, or contaminated fluid in a 400 series. We diagnose the actual cause before recommending anything. Many of these units are worth repairing and will run another decade with the right parts. If the operator is older than fifteen years and the gate itself is also failing, replacement often costs less than repeated repairs. We’ll show you the numbers either way, and you decide. Call (806) 484-1837 for an honest diagnosis.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Euless and nearby areas.