FAAC Gate Parts & Welding Nationwide

FAAC Gate Parts & Welding in Euless: What to Know First

FAAC gate parts and welding in Euless typically run $225 to $1,400 depending on whether we’re replacing a worn hinge or rebuilding a post that’s rotted at the base, and most repair jobs are completed in a single visit. We’re an independent FAAC service provider, not a factory-authorized shop, which means we’ll tell you straight when an OEM part matters and when a quality aftermarket equivalent does the same job for less. Most FAAC parts are on our trucks or sourced locally within a day or two.

Call (806) 484-1837

This page is for Euless homeowners with a FAAC swing or slide gate that’s sagging, grinding, or refusing to close square. Victor Salinas and our crew have worked on FAAC operators across the Mid-Cities for years, and we’ve seen every failure mode these gates can throw at a homeowner. Call (806) 484-1837 and a real person answers, day or night.

How FAAC Products Fail - and How We Fix Them

• Hinge weld fatigue on FAAC swing gate arms. The 412 and 415 operator models are strong, but they transfer a lot of force through the gate hinge points. In Euless clay soil, gates settle unevenly, and that puts constant twist on the hinge barrels. We regularly see the hinge-to-post weld cracking from years of that uneven load. Fix: grind out the old weld, re-square the gate leaf, and lay a full-penetration weld with proper preheat so it doesn’t crack again next spring.
• Bent or broken gate brackets on the FAAC 390 series. The articulated arm brackets are cast, and when a gate gets shoved by wind or a car bumper, the bracket snaps before the operator does. That’s by design, but homeowners get stranded. We stock replacement brackets and can usually swap one in under an hour without pulling the operator off its mount.
• Slide gate roller collapse under FAAC 844 operators. The 844 is a workhorse for Euless driveways with a slope, but it’s only as good as the rollers under the gate leaf. When a roller bearing seizes, the gate drags, the operator pulls harder, and the limit switch never sees the gate fully closed. We replace rollers in pairs with sealed-bearing units rated for Texas heat and dust, then re-set the FAAC limit and force parameters so the operator stops fighting the gate.
• Post rot at the base on older FAAC installs. In Euless, decades of wet springs and dry summers rot steel posts right at grade, especially where sprinklers hit them. A FAAC operator can’t compensate for a post that’s flexing two inches at the top. We cut the post below the rot line, sleeve and weld a new section, and add drainage gravel so the repair outlasts the original.
• Latch and lock misalignment on FAAC double-leaf gates. The FAAC E024U control board works fine, but the physical latch is dumb metal, and when one leaf sags a quarter inch, the latch misses the receiver and the magnetic lock won’t engage. We shim or reweld the latch plate, then run a full open/close cycle to confirm the operator’s entrapment sensors still see the gate correctly.

Our FAAC Gate Parts & Welding Process

1. 1
   We show up when we said we would. Every call starts with an honest arrival window, and the tech who shows up is background-checked and in uniform. No fifth-hand subcontractor.
2. 2
   We diagnose the whole system, not just the part that’s screaming. A cracked weld is often a symptom, not the disease. We check post plumb, hinge alignment, roller condition, and operator force settings on every FAAC job so we fix the root cause, not the noise.
3. 3
   We make the parts decision with you, at your gate. Where FAAC OEM parts are the right call for warranty safety or fit, we use them. Where a proven aftermarket equivalent does the same work for less, we tell you and let you decide. You get the price before we start.
4. 4
   We do the welding right the first time. Proper prep, proper rod, proper penetration. Victor’s father was a welder, and that standard never left the shop.
5. 5
   We test the full cycle and then some. Five open/close cycles minimum, sensor check, force settings verified. If it’s a slide gate, we run the rollers through their full travel.
6. 6
   We hand you a written 90-Day Done Right Promise before we drive off. If something isn’t right within 90 days, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Parts & Welding Costs in Euless

Here are the ranges we typically quote for FAAC gate parts and welding work in Euless. Every price is agreed before a single bolt is turned.

• Hinge replacement (single leaf): $225 to $480, depending on hinge size and whether the post needs weld repair in the same visit.
• Post replacement or reinforcement: $400 to $1,100. Digging through Euless clay takes time, and the steel must be set plumb before any weld is laid.
• Gate roller replacement (slide gate, pair): $180 to $380. Sealed bearings cost a bit more, but they survive Texas summers better than open-bearing units.
• Custom welding repair (cracked rail, broken picket, gate leaf re-square): $150 to $700, depending on weld length and whether we need to remove the gate leaf to do it properly.
• Latch and lock realignment: $140 to $320, including testing with the FAAC operator to confirm the gate locks every single cycle.

What moves the price is what we find once the gate is off its hinges, which is why we quote before we start and never after. Estimates are free. Call (806) 484-1837 and we’ll walk the gate with you.

Why Euless Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been serving Euless and the surrounding Mid-Cities for over 42 years, and we plan to be here for another forty. That changes how we weld. A gate post we set in 1987 is still standing because we don’t cut corners on buried steel. A FAAC operator we serviced last month will get the same level of care if it calls us back in a decade.

Our techs work on nine automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so when a FAAC part interacts with a different brand’s accessory or an older gate leaf, we understand the whole system, not just the FAAC half of it. Every job is backed by the 90-Day Done Right Promise, in writing. A live person answers at (806) 484-1837 twenty-four hours a day. And if you’re 55 or older, or served in the military, you get a permanent 5% discount. Done right, and backed in writing.

FAQs