Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Irving
Gate motor and opener repair in Irving typically runs $285-$680 for most single-family repairs, and our crews reach every part of the city within 60 to 90 minutes on emergency calls. Since 1984, Ironworks Gate Co. has worked the specific mix of gated communities, estate drives, and corporate campus entrances that define Irving. If your gate is grinding, refusing to open, or throwing a fault code, call (806) 484-1837 and a live person answers, day or night.
Why Ironworks Gate Co. Is Irving’s Preferred Gate Motor & Opener Company
Irving homeowners know their gates live a harder life than most. The Blackland Prairie clay under Las Colinas and the older neighborhoods west of MacArthur Boulevard heaves with every wet-dry cycle, and a gate that ran true for twenty years will begin fighting its own operator. We have corrected post lean, rebuilt rack and pinion drives, and replaced burned-out motors on more Irving gates than we can count. The work holds because we address why the motor failed, not just what broke.
Our Gate Motor & Opener crews arrive in uniform, background-checked, and carrying parts for nine major brands so the correct repair happens on the first visit. Victor Salinas, who leads our Irving service team, has spent years tracing faults that other shops misdiagnosed, especially on the legacy FAAC and Elite operators scattered through Las Colinas. We show up when we say. We quote the price before any bolt turns. And every job carries our written 90-Day Done Right Promise.
Our Gate Motor & Opener Services in Irving
Motor Installation
A complete motor and opener installation on an Irving single-family driveway gate usually runs $1,450-$3,400, depending on gate weight, run length, and whether we’re converting from manual operation. We set the operator on a plumb, properly footed mounting pad, because Irving’s expansive clay will punish a skimped foundation within two seasons. We also handle the full electrical run, safety edges, and entrapment protection so the finished gate meets current UL 325 requirements.
Motor Repair
When an opener fails in Irving, the root cause is usually not the motor itself. In Las Colinas HOA communities and the estates along the canals, we replace dead limit switches, cracked plastic gearboxes, and failed control boards that generalist shops misread as a burned motor. A straight capacitor or limit-switch repair typically costs $185-$420, and we will not sell you a motor you do not need. Victor and the team test every component before recommending anything.
Linear Motor
Linear swing-arm operators dominate Irving’s 1980s and 1990s ornamental gates, especially in the Cottonwood Valley and Valley Ranch sections of Las Colinas. These units push their worm gear hard when the gate post has shifted, and the arm twists or shears a pin. A typical linear operator replacement in Irving runs $1,200-$2,600 installed, including realignment and safety recalibration. We keep common linear arms and boards on the truck.
Slide Motor
Cantilever slide motors serve the wider driveways on Irving’s north side and the heavier commercial gates at Las Colinas corporate campuses. When clay movement or ice events bind the track, the motor strains until the chain jumps or the gear strips. Slide motor repair in Irving averages $320-$720; full retrofit of a slide motor onto an older wheel-only tubular-steel gate runs $2,200-$4,800 depending on track length and gate mass. We fabricate and weld the mounting in-house, so the retrofit fits your gate rather than forcing your gate to fit a kit.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Irving
We’re trained and equipped on nine automation brands, including LiftMaster, FAAC, BFT, and Mighty Mule. The FAAC line matters deeply in Irving, because dozens of Las Colinas HOA entrances were specified with FAAC swing operators during their original buildout. We stock boards, limit switches, and gear kits for those legacy units, which means your gate is not down for ten days while a shop “checks with a supplier.” If you own an Elite or BFT operator, we carry those parts too.
Common Gate Motor & Opener Problems We See in Irving Homes
- Post heave from Blackland Prairie clay. Seasonal swelling pushes gate posts out of plumb, which torques the operator arm and strips rack-and-pinion teeth. We re-pour footings with deeper, bell-bottom piers so the correction survives the next dry spell.
- Ice-damaged gearboxes and hydraulic lines. Winter Storm Uri froze and cracked operators that were never rated for sustained cold. We replace plastic gear cases with cold-rated units and repack or replace hydraulic seals on campus gates.
- Misdiagnosed FAAC and Elite control boards. A dead limit switch or dry solder joint gets called a “bad motor” and a $1,800 replacement gets sold. We bench-test the board first; often the fix is a $90 switch and thirty minutes of labor.
- Worn shear pins and twisted swing arms. When a gate sags even three-quarters of an inch, the linear arm fights it on every cycle until the shear pin fails. We align the gate, replace the pin, and reset travel limits so the motor is not doing the gate’s work.
Pricing for Gate Motor & Opener in Irving, TX
Here is what Irving homeowners and facility managers can expect. A basic control board replacement: $285-$520. Limit switch and capacitor work: $185-$420. Gearbox rebuild on a linear or slide operator: $340-$760. Full motor replacement on a single swing gate: $1,200-$2,900. Full slide operator replacement: $2,200-$4,800. New installation with electrical run, safety edges, and keypad: $1,450-$3,400. Every estimate is written, itemized, and agreed before work begins, so the invoice never surprises you.
| Service | Typical Irving Price Range |
|---|---|
| Control board replacement | $285-$520 |
| Limit switch / capacitor repair | $185-$420 |
| Gearbox rebuild | $340-$760 |
| Swing motor replacement | $1,200-$2,900 |
| Slide operator replacement | $2,200-$4,800 |
| Complete new installation | $1,450-$3,400 |
We Also Serve Cities Near Irving
While this page is written for Irving homeowners, our crews regularly cross into Grand Prairie, Coppell, Euless, and Grapevine for the same gate motor and opener work. If you live just outside the city line, the same 90-Day Done Right Promise and the same live-answer phone apply.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Irving
The motor is almost never the root cause. In the Cottonwood Valley and Valley Ranch sections of Irving, we see post heave from Blackland Prairie clay push gates out of plumb until the swing arm binds and the motor overdraws current until it fails. We correct the post footing first, then replace the motor, or you will be replacing it again in eighteen months. Call (806) 484-1837 and we’ll diagnose it properly.
Yes. We fabricate the track, mounting brackets, and chain drive in-house, then weld them to your existing gate structure so the finished unit runs like it was designed that way from the start. A typical retrofit on an Irving residential gate runs $2,200-$4,800. We quote the exact number before any cutting or welding begins.
Hydraulic operators not rated for sustained subfreezing temperatures will crack seals and lock up when Irving gets a Wedgewood-level ice event. We drain, re-seal, and refill them with cold-rated fluid, and we can install a battery backup and heater element so the next freeze does not strand the gate. Call for a free assessment.
UL 325 requires working safety photocells and a reversing edge or contact sensor on every automated gate. On many 1990s Las Colinas HOA gates, the photocells are original and aged out of spec. We test, replace, and recalibrate them on every service call, and we will show you the test on site.
Yes. We keep FAAC and Elite boards, limit switches, and gear kits for the legacy swing operators that dominate Irving’s Las Colinas HOA entrances. That is the difference between a same-week repair and a six-week wait for a part that was never in the local supply chain.
The Las Colinas Gate Reality
No other city in DFW has the density of gate work that Irving’s Las Colinas does. One of the largest master-planned developments in the country packed dozens of HOA gate entrances and corporate campus security gates into a few square miles. That means our Gate Motor & Opener technicians service more legacy FAAC and Elite swing operators per square mile here than almost anywhere in the metroplex. The parts shelf in an Irving truck looks different from one serving Grand Prairie or Coppell, because the machines are older, the tolerances are tighter, and the stakes at a Fortune 500 campus gate are high. We carry what those gates actually need.
In the Cottonwood Valley section of Las Colinas, our crew was called to a 1990s ornamental wrought-iron swing gate that had seized and was pulling the operator’s worm gear hard enough to shear its shear pin. We found the hinge post moved 1.5 inches out of plumb from Blackland Prairie clay swelling; after re-pouring the post footing with a deeper, bell-bottom concrete pier, we aligned the rack and pinion on a rebuilt FAAC 741 operator and calibrated the safety photocells to UL 325. The gate now sweeps silently and holds alignment through wet-dry cycles. That is the standard we bring to every Irving gate, from a 600-pound HOA entrance to a 40-year-old ranch-house retrofit on the west side.
Call Ironworks Gate Co. for Gate Motor & Opener Service in Irving
If your gate motor is grinding, stuck, or dead, call (806) 484-1837. A live person answers, day or night, and we’ll schedule a service window that works for you. The estimate is free, the price is settled before work begins, and every repair carries our written 90-Day Done Right Promise. We also honor a standing $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount. One call to Ironworks Gate Co. and the gate that has been fighting you for months will close like the day it was hung.
Written by Victor Salinas, Owner at Ironworks Gate Co., leading gate motor and opener service across Irving, Texas.