Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Hurst
When your gate opener stops working in Hurst, you need a crew that understands why it failed. We do. Most gate motor failures we see in Hurst trace back to the ground itself: the Blackland Prairie clay that heaves and shifts through North Texas seasons. That means a motor that won’t hold its limits, a gate that binds mid-cycle, or an opener that burns out early often has the same root cause sitting 18 inches below your hinge post. We diagnose the whole system, not just the electronics. Call Ironworks Gate Co. at (806) 484-1837 and we’ll send a technician who knows Hurst soil, Hurst housing stock, and the openers that hold up here.
Key Takeaways
- Gate motor repair in Hurst typically runs $180-$520 depending on the failure. Full operator replacement with installation averages $950-$2,400.
- Most recurring gate opener problems in Hurst are structural: shallow 1960s-70s posts heaving in Blackland Prairie clay, not electronics.
- We service nine major brands including LiftMaster, FAAC, BFT, and Mighty Mule, and carry common parts on the truck.
- A live person answers our phone 24/7. No voicemail trees.
- Every completed job is protected by our written 90-Day Done Right Promise.
Why Ironworks Gate Co. Is Hurst’s Preferred Gate Motor & Opener Company
We didn’t set out to be the loudest gate company in the Mid-Cities. We set out to be the one homeowners call when a gate has failed once and they don’t want to deal with it again. Victor Salinas, our owner, built Ironworks Gate Co. on that measure. We’ve been doing this work since 1984, and our technicians are trained on nine opener brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Whatever sits on your driveway, one of our people knows it cold.
Hurst is the kind of place where a gate gets installed and expected to work for twenty years. The homes were built in the 1960s and 70s. The gates are second and third generation. The soil underneath them hasn’t changed. Our crews have worked every Hurst neighborhood from Bellaire Heights to the streets around the NE Mall, and we know what those old ranch-style lots do to a gate post. When a Hurst homeowner calls us, they get a technician who already knows what he’s likely to find before he opens the first panel. That saves time and saves money.
We also know the response times that matter here. Dispatch for Hurst is coordinated from our Dallas-Fort Worth office, and our local crews serve Hurst directly. A live person answers every call at (806) 484-1837, day or night. Not an answering service. A person who can tell you when a tech will pull up.
Our Gate Motor & Opener Services in Hurst
Motor Installation
We install new gate operators on Hurst properties the right way, which means starting with the post, not the motor. A swing gate operator mounted on a post that’s only 24 inches deep will fight the clay every season until the limits wander, the gears strain, and the board gives up. We set posts below the active shrink-swell zone, square the frame, and then mount the operator. A typical new gate motor installation in Hurst runs $950-$2,400 including labor, and you’ll get a written price before we start. No surprises on the bill.
Motor Repair
When a gate motor in Hurst dies, we find the actual cause. Sometimes it’s a capacitor, a limit switch, or a control board. Often it’s the post torqueing the frame out of square and overloading the operator. We fix the mechanical problem and the electrical problem so the motor doesn’t fail again in eight months. Most motor repairs in Hurst run $180-$520 depending on parts and the condition of the post and frame. We quote the repair before any work begins.
Linear Motor
Linear gate motors are common on Hurst driveways with sliding gates, and they’re a good fit for the heavy gates you see on acreage lots and long rural-style entrances around the Hurst area. A linear motor pulls a rigid arm rather than swinging a hinge, which handles a heavy gate better than a swing operator. But the same clay heave that torques a swing gate can also shift the track or the gate itself, binding the drive. We install and repair linear motors with attention to the whole run: track, wheels, end stops, and the opener’s travel limits.
Slide Motor
Wide gates on Hurst acreage and rural properties generally want a slide motor. They handle more mass and greater span than swing operators, and they don’t rely on hinge posts that shift with the clay. The weak point on a slide setup is the track alignment: a fence post that’s leaning out of plumb will drag the gate off its rollers and burn the motor. We repair slide motors and the rails they ride on so the gate travels true. If your slide gate grinds, catches, or stops halfway, call us before the motor overheats.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hurst
We’re certified on LiftMaster, FAAC, BFT, and Mighty Mule, along with five other major gate-automation brands. That matters when an older opener has a discontinued board or an odd limit configuration. Our trucks carry common control boards, capacitors, and limit switches for the openers we see most in Hurst: LiftMaster and Mighty Mule on newer installs, FAAC and BFT on older estate gates. If it’s not on the truck, we can usually have it in hand fast, since our parts network is built around the DFW supply chain.
Common Gate Motor & Opener Problems We See in Hurst Homes
- Limit settings that keep slipping after rain. This is the signature Hurst gate failure. Spring rain swells the Blackland Prairie clay, the hinge post tilts, and the gate’s travel arc shifts just enough that the opener’s limit switch no longer matches reality. The motor runs too far, slams the gate, or reverses early. The fix is the post, not the board.
- Solar openers running dead after stormy weeks. Overcast stretches in the Mid-Cities can leave a solar-charged opener with no reserve. If the gate is your only access for livestock or vehicles, that’s a real problem. We install battery backup systems sized for the panel and the gate’s daily cycles.
- Corroded hinge pins overloading the motor. Fifty-year-old wood privacy gates in Hurst neighborhoods often have original or early-replacement hinges. Corroded pins bind, the motor pushes against resistance it wasn’t designed for, and the thermal cutoff trips. We replace hinges and repack posts before the motor cooks itself.
- Undersized operators on wide gates. A gate opener sized for a light residential swing gate can’t run a 16-foot farm gate on a clay-shifted post. The motor strains, overheats, and fails early. We size the operator to the gate’s actual weight and span, not the original builder’s guess.
Pricing for Gate Motor & Opener in Hurst, TX
Here’s what we tell Hurst homeowners, straight. Gate motor repair in Hurst runs $180-$520 depending on the part and the condition of the frame. Full operator replacement with a new motor and proper post work averages $950-$2,400. Solar retrofit with battery backup runs $600-$1,800 over the base opener. An $89 Seasonal Tune-Up covers adjustments, lubrication, and a full safety-sensor check, and we recommend it every spring and fall in Hurst because of the clay movement. Every price is written, agreed, and signed before we turn a bolt. Every job carries our 90-Day Done Right Promise in writing.
We Also Serve Cities Near Hurst
Our Gate Motor & Opener crews serve Hurst daily and cover the neighboring Mid-Cities communities along the same routes. That includes North Richland Hills, Bedford, Colleyville, and Haltom City. If you’re in any of those areas and your gate has stopped or is acting up, you’ll get the same local service. Call (806) 484-1837 and talk to a person, not a machine.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Hurst
Because the clay under your hinge post is expanding the same week your opener is trying to hold its travel arc still. In Hurst, the Blackland Prairie soil swells dramatically with spring moisture, and that heave tilts the post just enough that the gate’s swing path changes. The opener’s limit setting no longer matches where the gate actually stops. The permanent fix is resetting the post to 36 inches below grade, below the active movement zone, and then re-setting the limits. Call (806) 484-1837 for a free estimate on the post work and the opener adjustment.
Yes. Solar gate openers are a practical solution for rural and acreage driveways around Hurst where trenching mains power would run thousands of dollars. The catch in the Mid-Cities is that overcast spring weeks can leave a panel undercharged. We size the panel to the gate’s daily cycles and add a battery backup sized for at least five days of no sun. That keeps the gate alive for livestock and vehicle access through stormy stretches. A typical solar opener installation near Hurst with battery backup adds $600-$1,800 over the base operator. Call us for a written quote.
Most of the time, you need the post fix first. On Hurst homes built in the 1960s and 1970s, the original gate posts are often only 18-24 inches deep, which is too shallow for the active clay zone. The post shifts, the frame sags, and the motor has to work twice as hard to move the gate. Replacing the operator without addressing the post puts a new motor on a bad foundation. We diagnose both, and we’ll never sell you an operator you don’t need. Call (806) 484-1837 for an honest assessment.
Yes. Automatic gate operators in Hurst, and everywhere in Texas, are governed by UL 325 safety standards that require entrapment protection: photo eyes, edge sensors, or both, depending on the gate type and installation. A gate without working safety devices can seriously injure a person or a child. We test and replace safety edges and photocells on every job we touch, and we won’t leave a gate operating without compliant entrapment protection. If your safety sensors are older, misaligned, or absent, that’s a repair we’ll flag immediately.
For a wide farm gate on Hurst’s shifting clay, a heavy-duty slide motor or a properly reinforced linear motor will generally outlast a swing operator. Swing gates put all their weight on hinge posts, which are exactly what the clay wants to move. A slide gate rides on a track instead, and the operator pushes in a straight line. The post movement is still an issue for the track, but the loads are friendlier. We’ll size the operator to the actual gate weight and span, not a label on a box. Call (806) 484-1837 and we’ll come measure it for free.
If your gate motor in Hurst is failing, sagging, or just won’t hold its settings, call Ironworks Gate Co. at (806) 484-1837. We’ll send a Hurst-area technician who knows the soil, the housing stock, and the opener brands. Free estimates on every job. Written price before work begins. And when it’s done, it’s done right, backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Hurst since 1984.