Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Hurst
Gate access control in Hurst usually means one of three things: a keypad that has stopped reading codes, an operator that trips the safety photocell after every rain, or a system that works fine until the gate post shifts and binds the frame. We fix all three, and we fix them in a single visit more often than not. Ironworks Gate Co. has been doing gate work since 1984, and our crews know the Hurst housing stock: brick ranches off Pipeline Road, split-levels in Bellaire Heights, and the tight shared driveways that run through the older parts of town. If your gate will not open, call (806) 484-1837 and a live person answers, day or night.
Why Ironworks Gate Co. Is Hurst’s Preferred Gate Access Control Company
We are not a general handyman service that happens to do gates. Gate access control is the only work we do, and we have been doing it for over 42 years across the DFW Mid-Cities. That matters in Hurst because this city has a specific problem other suburbs do not share to the same degree: clay. Blackland Prairie clay runs under most of Tarrant County, but Hurst’s 1960s and 1970s builders set a lot of gate posts shallow, often 18 to 24 inches deep. That is not deep enough for soil that swells with every spring rain and contracts through every summer drought. The post heaves, the gate binds, and a keypad or remote command that should open the gate just clicks and does nothing. We see this pattern constantly in Hurst neighborhoods, and we know how to correct it properly, not just adjust it until next season.
Our Hurst customers call us because we show up when we say we will, we price the job before we turn a wrench, and every job is covered by our written 90-Day Done Right Promise. No paperwork to file, no arguing. If it is not right, we come back and make it right. Victor Salinas leads the company, and he set the standard decades ago: the 400th job gets the same care as the first.
Our Gate Access Control Services in Hurst
When a Hurst homeowner calls about gate access, the conversation usually starts with a symptom. The gate will not open from the keypad. The remote works intermittently. The phone entry app says the gate is closed when it is clearly open. Here is how we work through the most common access control jobs in Hurst.
Keypad Entry
A keypad entry system should read a code and open the gate, every time. In Hurst, the failure is often not the keypad itself. When the hinge post heaves from clay movement, the gate pulls out of square and the latch does not line up. The keypad sends the signal, the operator runs, and the gate stalls. We test the entire chain: keypad, wiring, operator, hinges, and post footing. Then we fix what is actually wrong. Keypad replacement in Hurst typically runs $275 to $550 installed, depending on whether we need to run new low-voltage wire.
Remote Control
Remotes and receivers fail in predictable ways, and North Texas weather accelerates some of them. Heat kills batteries faster than expected, and moisture from spring storms gets into older receivers mounted on unsealed posts. We stock replacement remotes and receivers for all nine brands we service, and we carry them in the truck. Most remote control repairs in Hurst are done on the first visit, with a new remote programmed and tested before we leave the driveway. Typical cost for a replacement remote and reprogramming runs $85 to $165 per remote.
Phone Entry
Phone entry systems let you open the gate from an app or a call, which matters a lot for Hurst residents who get deliveries on streets where a swing gate blocks the front walk. These systems are convenient until the cellular module loses signal or the app stops talking to the operator. We install and repair phone entry systems on existing gates, and we make sure the system works with the gate’s current operator, not against it. A basic phone entry upgrade in Hurst typically runs $450 to $850 installed, including programming and testing.
Card Reader
Card readers show up more often on Hurst properties with multiple drivers, or on small private streets where several homes share one gate. The reader itself is simple, but the wiring is not. Old card readers in Hurst are frequently wired with direct-burial cable that has degraded over 40 years in clay soil. We replace the cable, install a weather-rated reader, and program the cards on site. Expect $600 to $1,100 for a full card reader replacement with new cable run.
Video Intercom and Smart Access
Video intercoms are a growing request, especially from Hurst homeowners who want to see who is at the gate before they open it. We install video intercoms that tie into an existing gate operator and work with your phone, so you can see and speak to a visitor from anywhere. These systems can be added to older access control setups, but the gate itself needs to be structurally sound first. If the post is heaving, a video intercom will not fix it. We address the structure, then add the smart hardware.
Loop Detector and Safety Photocell
Here is an area where Hurst’s geology directly affects the equipment. A loop detector buried in the driveway senses a vehicle and holds the gate open. When the clay shifts, the loop can crack or the sensitivity drifts. A safety photocell, the beam across the gate opening, gets knocked out of alignment when a sagging gate or shifted post breaks the beam path. We sell and install loop detectors and safety photocells, and we set them so they hold up through Hurst’s wet-dry cycles. Photocell replacement or realignment runs $150 to $300. A new loop detector, including saw-cutting and sealing the driveway loop, runs $500 to $900.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hurst
We are trained and equipped on nine gate-automation brands, including Viking, Ghost Controls, Linear, and BFT. That matters when you have a Gate Access Control system that was installed a decade ago and the original installer is gone. We service what is on your driveway, whatever the brand. We also keep common parts on our trucks: receiver boards, remotes, photocells, and keypads. For Hurst customers, that means we rarely have to order a part and come back next week. If it is a common failure and we carry it, it gets fixed the day we arrive. Our technicians work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and we do not play favorites. The right fix is the one that matches your equipment.
Common Gate Access Control Problems We See in Hurst Homes
- Post heave from Blackland Prairie clay torques the gate out of square. The keypad sends the command, the operator hums, and the gate stalls because the latch no longer lines up or the panel binds against the post. This is the single most common access control failure we see in Hurst, and it comes back seasonally unless the post is reset below the active clay zone.
- Shallow 1960s and 1970s post footings let swing gates drag on driveways. After spring rains, the soil expands and lifts one post more than the other. The gate drags, the safety photocell beam breaks, and the operator freezes for safety. The access control system looks broken. It is actually a footing problem.
- Winter ice storms crack wooden rails on shared driveway gates. Ice builds on horizontal members, adds weight, and splits the rail. The gate sags off the rack and pinion, and the system reports a fault instead of opening. Hurst gets these storms hard, and gates take the damage.
- Old direct-burial cable that has degraded in clay soil. Many Hurst gates built before the 1980s used cable not rated for wet, shifting soil. The insulation breaks down, the keypad or photocell shorts intermittently, and the system works one day and not the next. We replace the cable and the problem goes away.
Pricing for Gate Access Control in Hurst, TX
Here are honest numbers for Hurst. A keypad replacement runs $275 to $550. A new remote and programming runs $85 to $165. A phone entry system installed on an existing gate runs $450 to $850. A card reader with new cable runs $600 to $1,100. A video intercom added to an existing operator runs $700 to $1,400, depending on the hardware and whether we need to pull heavier wire. A loop detector, including saw-cutting and sealing the driveway, runs $500 to $900. Photocell replacement or realignment runs $150 to $300. And if the underlying problem is a shifted post, expect $350 to $700 per post to dig it out, reset it below the clay zone, and haul in proper concrete.
Every price is quoted and agreed before any work starts. You know the number before we turn a bolt. We also offer a Free Second Opinion on any written estimate you have from another company, $50 Off Any Repair Over $250, and a permanent 5% Senior and Veteran discount. Call (806) 484-1837 and we will give you a real price over the phone or schedule a visit.
We Also Serve Cities Near Hurst
Our crews regularly work across the Mid-Cities corridor, so if you are in Hurst or just across the line in North Richland Hills, Bedford, Colleyville, or Haltom City, you are in our service area. The same crew, the same 90-Day Done Right Promise, and the same straight pricing. We are the Gate Access Control team that handles the whole area, and we schedule service so we are there when we say.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Hurst
Because the Blackland Prairie clay under your gate post is swelling with moisture and lifting the post, which torques the gate frame out of square. The keypad sends the signal, the operator starts, and the gate binds or the safety photocell trips. It is not a keypad problem. It is a post heave problem, and the only permanent fix is resetting the post below the active clay zone. We do that work in Hurst regularly, and we can tell you on the phone whether that is what you are dealing with. Call (806) 484-1837 for a straight answer and a free estimate to correct it.
Yes, in many cases. Hurst has a lot of shared driveways and tight setbacks, especially in neighborhoods built before the 1980s. A slide gate runs along the fence line instead of swinging into the driveway, so it can often fit where a swing gate will not. The catch is that the gate needs room to slide and a level run to travel on. We survey the driveway, measure the available side clearance, and give you a written price before committing to anything. A slide gate conversion in Hurst typically runs $3,500 to $7,000, including operator, track, safety photocells, and installation.
Not unless the post is reset first. A smart access system, a keypad, a video intercom, a phone entry module, will all fail on schedule as long as the post is heaving with the clay. We see original Hurst posts set 18 to 24 inches deep all the time, and they shift every wet-dry cycle. The proper fix is to reset the post at 30 to 36 inches, below the active shrink-swell zone, in a proper concrete footing. Then the new access system will hold its alignment. We reset the post, install the system, and back both with our 90-Day Done Right Promise. Get a free site review by calling us.
Yes. We add video intercoms to existing gate operators on homes all over Hurst, including the older neighborhoods around Bellaire Heights and the streets off Pipeline Road. The work involves mounting the intercom station, pulling new low-voltage wire if the old cable is degraded, and programming the app to your phone. If the gate itself is out of square from post heave, we address that before installing the intercom, because a video intercom on a binding gate is wasted money. Expect $700 to $1,400 for a typical video intercom addition on an older Hurst gate, and you will have a written price before we start.
Yes. Automatic gate operators are required to have entrapment protection per UL 325, and that means safety photocells, an inherent entrapment sensor in the operator, or both. This is not optional on a new gate installation or an operator replacement, and we will not install or leave a gate without it. If your existing Hurst gate is missing photocells or they are permanently bypassed, that gate is not safe and it is not code-compliant. We inspect and correct entrapment protection as part of every access control job. Call (806) 484-1837 to have yours checked.
We dispatch to Hurst typically same-day for gate emergencies, and we answer the phone 24 hours a day, 7 days a week. A live person takes your call, not a voicemail tree. If your gate is stuck open and your property is unsecured, or stuck closed and you cannot get your car out, say so when you call. That gets priority. We will give you a straight arrival window and a straight price before we send a truck.
No. Our pricing is the same across the Mid-Cities. A keypad replacement in Hurst costs the same as in Bedford or North Richland Hills: $275 to $550. What changes the price is the condition of the underlying gate. An older Hurst gate with a heaving post will cost more to make right than a simple keypad swap, because the post work is the real repair. The keypad was just the symptom. We quote the full job upfront, so you know the total before any work begins.
Call Ironworks Gate Co. for Gate Access Control in Hurst
If your Hurst gate will not open, opens too slowly, trips the safety beam, or just will not stay aligned, call us at (806) 484-1837. We will answer, we will ask the right questions, and we will give you a straight answer and a free estimate. We stand behind every job with our written 90-Day Done Right Promise. That is the Keystone Standard, and it has been for over 42 years. One call to a live person, one visit, and your gate works the way it should. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Hurst and the DFW Mid-Cities with gate access control, repair, and installation for over 42 years.